Deltashield HP 400 PW

Property	Data
Mixing ratio of Comp. A to Comp. B	1 : 1 by volume
Dry film thickness range [mm]	Steel Minimum: 1 Steel Maximum: indefinite Concrete Minimum: 2 Concrete Maximum: indefinite For project specific DFT recommendations consult with manufacturer.
Recommended thickness [mm]	Minimum: 1 Maximum: unlimited
Tack Free-Time at 20°C [sec.]	10 – 20
Over coat cycle [h]	0 – 12 (without any pre-treatment)
Curing/loading after [h]	Walkable: 1 Mechanical: 2 Chemical: 12 – 24
Temperature range for application (ambient) [°C]	-10 – +50°C
Temperature range for application (substrate) [°C]	-10 – +50°C
Material Temperature (Preconditioning) [°C]	25 – 30°C
Material Temperature (Spraying) [°C]	65 – 75°C
Maximal relative air humidity for application [%]	98%
Pay attention to the dew point limit	Substrate should be 3°C greater than DP (dew point)

Physical Properties

Property	Test Standard	Comp. A Data	Comp. B Data
VOC-content	DIN EN ISO 11890-1 / ASTM D-1259	0%	0%
Solids content	DIN EN 827 / ASTM D-2697	100%	100%
Viscosity [mPa*s] @ 25°C	DIN EN ISO 2884-2 / ASTM D-4878	600 – 1,000	500 – 900
Density [g/cm³] @ 20°C	DIN EN ISO 2811-1 / ASTM D-1217	1.09 ± 1.13	1.00 ± 1.04
Density [g/cm³]	EN ISO 1183 / ASTM D-792	1.01 ± 1.05	1.01 ± 1.05
Tensile strength [MPa]	ISO 37-2005 / ASTM D-638	≥ 20	≥ 20
Modul [MPa]	ISO 37-2005 / ASTM D-638	100% Elongation: ≥ 10 300% Elongation: 20	100% Elongation: ≥ 10 300% Elongation: 20
Elongation at break [%]	ISO 37-2005 / ASTM D-638	≥ 400 – 450	≥ 400 – 450
Hardness [Shore D]	ISO 868-2003 / ASTM D-2240	45 ± 5	45 ± 5

Property	Test Standard	Data
Rebound resilience [%]	ISO 4662 / ASTM	≥ 32
Tear growth resistance[N/mm]	ISO 34-1 method A	≥ 45
Volume abrasion [mm³]	DIN ISO 4649	≤ 130
Taber Abrasion [mg]	ASTM D-4060	< 6 (Wheel CS17 / 1.000g / 1000 Cycles) < 125 (Wheel H18 / 1.000g / 1000 Cycles)
Pull off strength [N/mm²]	DIN EN ISO 4624 / ASTM D-4541	Concrete: ≥ 1.5 Steel: ≥ 6
Max. Process temp. [°C]	ISO 11346 / ASTM D-2485	Wet: 80 Dry: 130 Peak temperature dry: 160
Water vapor transmission rate [g/m² *d]	ISO 15106-3	6.1 (at 23°C a. 85% relative humidity) 17.5 (at 38°C a. 90% relative humidity)
Permeation coefficient [gmm/m²d]	ISO 15106-3	17.3 (at 23°C a. 85% relative humidity) 51.0 (at 38°C a. 90% relative humidity)
Methane transmission rate [cm³/m²dbar]	ISO 15105-1	91.5 (at 23°C a. 0% relative humidity)
Resistance to Root Penetration	EN 14416	Passed
Crack bridging abilities [mm] (thickness of the sample 2-3 mm)	DIN EN 1062-7 Procedure C.2	+23°C: > 15.5 -10°C: > 6.8 -20°C: > 6.4
Fire protection classification	DIN 4102-Part 1	B2 (normally inflammable)
Coefficient of sliding friction	DIN 51131	Dry (leather): 0.78 Wet (SBR-rubber): 0.04
Sound absorption	–	Approx. 5 dB / mm DFT
Cathodic Disbondment depth [mm]	DIN EN 10290-2004 Class: A	23°C (28 days): 2.3 ± 0.7 60°C (2 days): 1.7 ± 0.6 80°C (2 days): 3.4 ± 1.1

Property	Test Standard	Data
Impact Resistance [J/mm]	DIN EN 10290-2004 Class: A	23°C: 9.0 -5°C: 7.0
Surface resistance [Ohm]	DIN IEC 60167	≥ 1.0*10^11
Volume resistance [Ohm]	DIN IEC 60093	≥ 1.0*10^11
Storage conditions [°C]	DIN EN 12701	10 – 30 (in closed original drums, stored at dry and well-ventilated place; beware of freezing)
Shelf life	–	Approximately 18 months unopened and stored correctly

All applicators of DELTAShield HP 400 should be trained and approved by the manufacturer.
Spray applicators should wear appropriate PPE including approved breathing equipment, eye wear, Nylex or similar light weight spray suit and appropriate covered footwear.
Avoid breathing in vapors during spraying or when handling chemicals.
Avoid eye and skin contact.
Store chemical drums in a cool dry environment. Avoid storing chemicals for long periods in direct sunlight.
Do not store chemicals next to food stuffs.
Ensure chemical drums are kept tightly sealed and avoid ingress of air and moisture.

DELTAShield HP 400 is supplied in 40 or 425 kg sets.